Re: Edison FW SFI Tables
Hi icpda, I will investigate on this and let you know if I find some useful information. RegardsSergio
View ArticleRe: Failed to start Hostapd on boot
you could take a look into the configure_edison script to understand how it works and which config files it changes yocto use systemd and the command to control systemd is systemctl the mean question...
View ArticleClik here to view.
Re: Fan noise from D54250WYK
Here is a "sushi inside-out roll" hybrid approach: A Streacom NC2 passive case, with an external 120mm fan undervolted to run off 5V USB power. Look at those chunky, deep case fins; this approach is a...
View ArticleRe: Failed to start Hostapd on boot
I want to use edison as AP with hostapd. I notice that on a fresh install, if I add hostapd at boot with "systemctl enable hostapd", it works fine.In my installation, I've some configurations maybe...
View ArticleClik here to view.
Re: Problem uploading sketches.
I figured this out. For unknown reasons, the C:\arduino-1.5.3-Intel.1.0.4\hardware\arduino\x86\tools\izmir\clupload_win.sh file was missing. Even reinstalling/repairing the Arduino for Windows...
View ArticleRe: Bluetooth communication Edison/phone
Hi, thanks for keeping to give some good help speccy88 you are right, I had it correct in /etc/bluetooth with 4 .conf files and in /usr/sbin/bluetooth_rfkill_eventBut for /usr/sbin/brcm_patchram_plus...
View ArticleWindows 8.1 or Windows 10 after update graphic, black screen on my Intel Nuc...
Best Intel, I have a problem of update:Graphics: Intel® HD Graphics Driver for Intel NUC 10.18.10.3621 (Latest) When I install Windows 7 64bit on my DN2820FYKH and update this Graphics software just...
View ArticleRe: New to Galileo. Boots, but sketches do not run, and I am unable to update...
Hi redruM69; The FVMAIN.fv let you recover the firmware but when you update it, you get an error, right?Is something stopping the update process, network connection or something wrong with the IDE...
View ArticleRe: PMBus in S2600CP Server board
We have some examples listed on a previous post of possible commands you may run to test the power supplies. You may use the Integrated BMC Web Console to monitor the status of the power supplies and...
View ArticleRe: Windows 8.1 or Windows 10 after update graphic, black screen on my Intel...
So what now? can I install windows xp 64? but does not because of SSD hard drive? Windows 7 is slow, I want to install windows xp, anyone know how?
View ArticleAutomatic switching between AP and STA
Hello, This is maybe more a generic Linux networking question, so it should be possible with the Edison. Is it possible to write a service that switches to AP mode if none of the authorized APs it...
View ArticleRe: MFSYS25 Switch module problem
How many switch modules are installed? If you have two switch modules, have you tried the recommendation posted earlier? From the CMM GUI, choose System | Switches | Advanced ConfigurationMouse over...
View ArticleRe: New Graphics card, PC won´t boot
Just after I posted the BIOS version, I noticed it did not update. So, I did the update via USB flash drive. It wen't through ok, but Win7 is failing to start. Keeps getting better! I'll reach back to...
View ArticleRe: Intel Core i7-4790 4K at 60Hz
Franck, as you mentioned on your post low voltage U versions of Haswell processors on NUCs are limited to 4k@30Hz. Based on the motherboard‘s specifications, the maximum resolution supported by it will...
View ArticleClik here to view.
Re: Automatic switching between AP and STA
hostpad/wpa_supplicant is opensource code with enough c/c++ knowledge you can implement whatever you want, thats the big benefit of opensource hostap-1 - hostapd/wpa_supplicant 1.x for example is the...
View ArticleRe: Connecting Galileo to Water Pumps for considerable head heights ~ 5-10...
Thanks for all of the info, the links are quite informative. I think this gives me enough confidence to move forward with the project now without frying my board.I will have to go ahead and purchase a...
View ArticleRe: Artifacts, white pixels, tearing on HD4000 on 3rd gen i7-3612QM when CPU...
Hello joe, Thanks for paying attention. I suspect that the issue is bound to the package temperature. I often use the CPU to 100% for several tens of seconds, because i am developing stuff. After that...
View ArticleArduino IDE won't launch in Windows 8.1
What I've tried1 Installing Java SDK and runtime2 add the %JAVA_HOME%\bin to Path environment variable3 JAVA_HOME environment variable pointing to the jdk...
View ArticleRe: Can you please present yourself?
Hi, My name is Robyn Farah, I am the director of a South African technology company called KAT-O. I am interested in using the Edison for various projects from creating interactive art and wearable,...
View ArticleRe: build and transfer my c/c++ code on ublinux
you dont upload to yocto, yocto is a build system and the output of this is a linux distribution named poky you can do the same with ubilinux (debian) you have gcc, g++, make, vi, nano and much more if...
View Article