Re: Update Utility 2.0 problem Only sees Wifi card
Thanks, looking forward to a resolution.
View ArticleRe: First day ok with 13V. Second day short circuit
hello Diego . I made the video feeding it to 9 volts .The current squirts to 10A !!! if I lower the limit the short circuit current is approximately 4 amps .There was smoke from R98 or CR9 did not see...
View ArticleRe: ubilinux (Debian) now available from Emutex Labs
@Charkoteow will do. My bandwidth right now is limited though. Will be in touch.
View ArticleRe: Edison thermal_zones - clarification/documentation
I believe the Quark SoC has much in common with the Edison, some info may be of interest in the Quark doc. Intel® Quark SoC X1000 Software Developer’s Manual for...
View ArticleClik here to view.
Re: Error: failed to retrieve Local System Account using MEI; error code -...
In case anyone happens upon this thread later, the HP 8000 Elite is an AMT 5.2 system. The 8200 is AMT 7.0 and supports Host based provisioning. He would have needed to find another provisioning...
View ArticleRe: D54250WYK Windows 8.1 low memory error
I did as well. Will post if I ever get any answer.
View ArticleRe: Build custom package in a new Yocto layer
To start with try `bitbake nano` and see if the ipk builds in tmp/deploy. I'm not entirely sure on your problem but I'd start with renaming your nano.2.26.bb to follow the nomenclature nano_2.26.bb as...
View ArticleRe: Gadget Driver stops working after a few seconds (ubilinux)
My personal suggestion is to configure wifi and ssh into the console over wlan. For console over usb, I'd use a serial UART tty connection.
View ArticleRe: Dedison, Hooking Edison to Anything voids warranty
deium wrote: jwestervelt, The Sparkfun battery layer was shipped without tape over the microUSB port and the Edison module likely was the victim of a known shorting issue. Sparkfun did not package it...
View ArticleRe: Gadget Driver stops working after a few seconds (ubilinux)
Thank you, the two methods you mention are the workarrounds I use atm, but they have drawbacks, the most important is performance, the serial console is good for commandline work but sharing files with...
View ArticleRe: Dedison, Hooking Edison to Anything voids warranty
jwestervelt, Agreed. But there was no mention of an Arduino or Mini Breakout board in the conversation this far.
View ArticleRe: Bleno nodejs module and Intel XDK IoT Edition v.0087
Hi Eric,I haven't access to the Edison now. I'll try to remember my workaround. Log on the Edison and change the directory to "/node_app_slot"Follow this article:...
View ArticleRe: Gadget Driver stops working after a few seconds (ubilinux)
if you're pairing to your iPhone, that is not utilizing the wireless but Bluetooth. Is there a way to utilize the wireless. G and N bands are much faster.
View ArticleClik here to view.
Intel® NUC Kits D54250WYKH BIOS settings and Overclocking
Hey. Here is the BIOS glossary doc: http://download.intel.com/support/motherboards/desktop/sb/biosglossary_nuc_v03.pdfBut it doesn't say anything else that can't also be read in the BIOS help text. So...
View ArticleClik here to view.
Re: Dedison, Hooking Edison to Anything voids warranty
i keep saying i'll put this down, but... the mini breakout has been part of the project. firmware was loaded on through the breakout. and then standalone tests were run with the battery board. so if...
View Article29/59 Bug on WMC with Intel 4600 Graphics
Is there a way to at least improve the jumpy video with the 29/59 bug in Windows Media Center 7? I have turned off Film Mode Enhancement and Contrast Enhancement in Advanced and Skin Tone Enhancement...
View ArticleRe: Serial I/O on J3 not responding
Deium, I used microusb B cable for MK20DX test. Did not make much difference. I have used J21 with correct polarity even before my USB to USB test...so that is not the issue.. I think I have busted the...
View ArticleRe: Serial I/O on J3 not responding
hk101, I am okay with the cable and power via J21. I don't have a program to test a FT232R,if it is possible to write this using c, gcc is installed on the Edison module. I wish I had more to offer...
View ArticleRe: SDK installation and Eclipse Integration?
yongpingWhat is the full path you are providing in the toolchain and sysroot locations?This should be the full path to the location where you installed the SDK which the default is:Toolchain:...
View Article